Major Airflow

So I just bought a Plumeveil 1.5 clone and love it so far. The only thing I can't figure out is how to adjust the airflow where drip tip is. Is there anyway to open it up without damaging it?  

so i have a COV ARIS atty that i bought about a year ago. i took it apart to try to increase the airflow, but got sidetracked on that project and put it on the back burner. Fast forward 6 months and i go to start the project again but i had lost the insulator to seperate the center post from the atty body. i tried contacting COV with no luck. Anyone have any ideas on where i could get an insulator for this? or if i could possibly make one?
thanks in advance
-Matt  

I just bought a new E Cig, the Adept Zlide kit - Adept Zlide Kit

My issue though is that within 6 hours I have replaced the liquid 3 times. It just goes down ridiculously quick, and I'm not really chainsmoking it.

Basically, how do I make the liquid last longer before replacing it, avoiding the obvious answer of "Don't vape it as much" haha. I'm not really familiar how airflow holes and wattage works, so perhaps I'm doing something wrong with that part of the E Cig. I've got my airflow fully open at the moment though, could that be why the liquid is going down so fast? Does more airflow cause more liquid to be used?

I'm using a 1.6ohm coil and my wattage is set to 14, which is the second lowest. Does less wattage use less liquid? Not sure if it's one of these or a combination of the two that is making the liquid go down so fast.

Thanks guys.  

Hi,

Just wondering how to get a good clean of dirt and juice residue buildup on airflow base part for tanks and rda's. I find this part to be the hardest to clean. Not sure if you can run it under water or just try and get into the itty bitty cracks and crannies with a paper towel like I currently do. The tanks I use are mainly Nautlus Minis and Subtanks. The RDA's are freakshow, derringer, tobh, magma, etc. HOW do you get a good clean on the AIRFLOW CONTORL BASE/VALVE​?  

Okay so for the time being I still have my protank 3 with airflow....until today was hitting good,now I'm not getting th airy draw I was....maybe airflow is a bit gunked?? Coil is fine n clean still,only few days use on this one so I don't believe it's that....ideas?  

I am having problems with my Hellvape MTL, it is not delivering a good flavor and has juice leaking through the airflow, I am currently using the 1.2 ohm coil that comes with the atomizer, I use juices nicsalt 35mg. I use the 3 holes and airflow in the 4 to 12-14w.  

I just got my Aspire Atlantis in, and to be honest I'm not at all satisfied, and I can't help but wonder.... Did I get a defective unit?

I bought it and the Kanger Aerotank Turbo quad coil tank. My resistance on the Kanger is registering at 0.9ohm and I'm sending about 23watts to it. The amount of vapor is excellent, flavor is good, and it's not an overly warm vape at all.

So then I slap on my Atlantis. The 0.5ohm is registering at 0.6 (big whoop...lol) and I'm sending 28 watts to it. First, the hit is BEYOND airy. I'm on the lowest airflow setting and there's no pull required at all. I believe it isn't sealed well somewhere along the airflow adjustment, because when I blow a bit of vapor back into it as a test, it comes out of the airflow hole (obviously) but it also flows out of other areas around the airflow ring. This doesn't happen with my Aerotank Mega, Aerotank Turbo, or my Nautilus...

Furthermore, the hit itself is just BAD. The flavor is off, the vapor is WAY too warm to be enjoyable, and where as I exhale nice sized clouds using the Aerotank Turbo, I exhale pathetic small clouds that aren't even thick when I use the Atlantis. Considering its a lower ohm with more watts going to it, how is that even possible??

So, no resistance at all on the airflow, even on its smallest setting, and obviously I have to be getting air from some areas around the airflow ring. The vape itself tastes bad (not burning cotton bad, just a bad flavor), and it's VERY warm. If I try and pull on this the way I do with the Turbo (only 0.3 ohms higher), I exhale a measly small thin cloud AND I often get choked when doing so.

So I'm just curious.... Is this the way this tank hits?? I can't believe how many praise it if so, I see no appeal. So I can't help but think I must have gotten a defective tank. I've tried lowering the watts down to about 22watts just to see, and even though the vapor wasn't AS hot, it was still uncomfortably warm and did not do my liquid's flavor any justice.

Any thoughts? I really would like to hear if this is how these new sub ohm clearos are going to hit, because if so I have absolutely no interest in making the switch.

Thanks in advance,
Finch  

Hello
I have the wotofo serpent rta top airflow single coil tank now and I just purchased the augvape druga rta. Flavor is 100% better in the augvape drugA rta but juice leaks out the bottom of the tank every time which is why I have to stay with top airflow as it never has leaked on me. So I’m looking for a top airflow rta single coil . I typically vape between 20-30watts so I don’t need a powerhouse. I just want the flavor and don’t care about clouds. Can anyone recommend the best top airflow rta? The wotofo serpent works well but it takes a hit on flavor. The serpent only has 2 small air holes around the coil area and I think this is why it isn’t producing a good vape. I was looking at the Zeus? Augvape intake of the dual one? Or any others anyone can recommend ?

primary goal: outstanding flavor
No leaking
Lots of air holes around the coil


thanks for your time  

I just picked up a Dark Horse Clone by Tobeco yesterday. I washed all the machine oil out, set it all up using kanthal and organic cotton, and it vapes great. The only problem is I literally get zero flavor AT ALL using it. Could it be that I am using to little cotton? I used to put a crap ton into my IGO-W (drilled airholes for more airflow). The same juices that used to taste so wonderful taste like nothing at all.

I am using dual 7-wrap micro coils with 26g Kanthal reading at 0.41ohms. Just wondering if there is anything I can do to get more flavor out of this bad boy. I have experimented with using different airflow amounts all to no avail. Any feedback is much appreciated!

Thanks,
Tyler  

I recently bought a Squape R clone from Fasttech,its ok but not what i was expecting, so i'm looking now to kinda move up in the RTA world, I can't afford an original svoemesto, erlkonigen or taifun, but is it worth getting a clone of one of these? my clone experience so far hasn't really been amazing, obviously its hard to differentiate between it being the fact its a clone or that, heaven forfend, i just don't like the squape style.

So heres the rub, do i try another clone of one of these other styles as a cheap way of seeing if i prefer another RTA style, or do i just stick the money into an original like the Lemo 2 ?

I'm not certain of what i really want to be honest whether its dual coil i need for the flavour and clouds i'm not getting from my squape r or if its down to the build deck/airflow/chimney/whatever but the hit from the squape only satisfies if i pre-heat it for a second and only take a quick puff then. otherwise its low flavour dry throat hit.