Right now I have a few box mods, the IPv3, SIG 150w and the Snow wolf 200w. I'm using the Snow wolf 200w and honestly I'm not happy with it. I've had the button stick a few times causing it to auto fire and I'm noticing an almost one second delay from when I hit the fire button to when an actual vape starts to kick in (very slow fire up time, and I'm only running dual twisted 26g) on top of that I really dislike that I have to hit the fire button to see how much volts I'm using. I know the SX M class is one of the best out right now, but the fact it's a single battery concerns me because I typically vape between .12-.20 ohms and usually 60-80w (but since getting the derringer it's been 60). I really like the hot, dense flavorful vapes and I wanna make sure if I get the SX M class it'll be able to deliver that.
Hello everyone I recently purchased an ipv mini v2 and I love it, it is working perfect. I only have one complaint the fire button rattles like crazy and it drives me nuts. To some it's not a big deal but I just don't like it. So do any of you out there know if there is a way for me to fix this? Once again everything else is perfect ohms and all that it's just the fire button. The wattage up and down buttons are supper tight and clicky. Any help would be greatly appreciated. Thanks
As the title states, I have a question. A little information to preface; I'm using a snow wolf mfeng ux mod with a tfv16 tank, vaping at 115 watts. This is a dual 18650 mod, and been vaping fine for a while, using different tanks and wattage too. Lately when I vape, it feels like the firing bar on the side vibrates long a spring slips from a seat and does that old school door stopper wobble and it stops, but doesnt do it for other fires when I vape. My batteries are clean/healthy and undamaged wraps, 510 sections for mod and tank is clean, batteries only ever used in this mod.
I dont know what could be causing this, so I came here. What do yall thing it could be??
Tl;dr: When I fire my regulated mod, I feel a slight buzzing or vibrating in the fire bar and it's not supposed to. What is, what do?
I've got a couple of these little mods and both have the same problem. They continue to fire after the button is released. When it happens the display changes to the power on/off and keeps firing until the unit restarts (presumably after the 15 second cut off?). I can only think that the mod is registering 3 presses when I fire which triggers the screen change, and there is a bug which stops the release of the fire button registering. Anyone experienced this? Any fix? I'm surprised it's happening with two units so it must be happening to someone else!
This is so funny. I wonder where the fire button is. It would be great if the tail acted like a trigger. It seems to have a removable drip tip, but you might be limited on ones with wider bases.....
Hi
I got myself second Caliburn and from the start I feel that auto firing is not as fast as my first one, just like a second or so behind. If I use the button it seems to be OK.
Also, it feels more airy. I check the same pod on both devices and first one seems to have a bit more restrictive airflow. Or, due to late auto firing, I am inhaling first clean air instead of vape, and thus, the feeling of less restrictive airflow.
And lastly, which is not a problem, but it is not feeling OK, second Caliburn pod latching thing feels more loose, where on the first, when I push pod into the slot, I can feel and hear distinctive click, on the second, just a very little bump and very shallow click.
Would first, auto fire delay constitute good grounds for warranty replacement? I got it less than a week ago.
Any thoughts?
Hey guys.. i been vaping for a while and not had this hapen before.. i am using a Hugo Vapor Rader and ot has been working with no problems until today... when i go to use it, when i try to fire, it says high atomizer the first time i push fire button followed by low battery (have tried multiple sets) when i press again. If i persevere and keep attempting to fire it works fine as if there were no problem until the next time i go to use the device when the process repeats.. i have taken the tank apart and cleaned and put back but the issue continues.. anyone have any ideas on what is wrong/what i should do?
Well this sucks, I have an iStick 30w and toptank mini, I ran out of pre made coils so I thought i would try the RBA of the toptank. At first it read out as “protection” upon trying to fire it (I think the ohms were too low on the pre made coils included with the RBA at .1), then it said low battery (it was almost fully charged) so i plugged it in and tried to fire it once more and the thing started smoking (no protection message this time, just a little puff of smoke within the LED window). I only fired the button for a split second and it still seems to be functioning. Not sure what I should do lol or just ditch out on it? It appears to be working yet but stinks like an electrical fire now. I’m kinda reluctant to use it (I still have an old coil but it was starting to taste funky). Any advice or idea what might’ve happened?
hi my smok 22 vape pen button is jammed in so the top bit is fully pushing in and the bottom is fully not pushed in. it’s not firing or anything when i don’t want it to so that’s good but it also won’t fire at all. idk how to add images
Hello very basic question I love dripping and do it all day my one problem is with the mech mods I have I cannot place them down with out locking them or they fire sometimes anyone know of a good clone that will not fire when placed down maybe one with a recessed button of sort?
I currently have a F U and a Stingray infinity
Hey everyone. I've noticed that just about every day since I've used it. When I hit the button to fire it, it will fire for a couple secons then stop, and then fires back up again. And it's starting to concern me. Does anyone else have this issue? And how would I go about fixing it?