Taste Issues With Kanger Subtank Mini.....

okay, so i had a problem yesterday where i would keep getting juice popping up on the draw, that problem is solved, however, now on only the second day of light use, on the 1.2 ohm coil that came with the tank i am getting a pretty harsh smokey taste. Its not overwhelming like it is when a coil is burnt out, just an unpleasant taste. I did 4 drops of liquid on the coil before using, everything is screwed in tight. Do i need maybe a couple more drops on the coil?

FYI: using an istick 30w burning at about 14.5-15w  

I'm using a Subtank Nano on the KBOX. Should be absolutely no problems.

But my coils (both the 0.5 and 1.0) are tasting awful. I prime them great, I make sure everythings good and secure, and I'm using a 75%-ish VG juice.

But I can't go above 20 watts with two new packs of coils I have, and especially on the 1.0 coils, that's ridiculous. I'll get a vaporized rubber taste that tastes like the worst clearomizer coil I've ever come across.

Dry cotton should just have sort of a cottony, almost doggy or smokey taste. But this is a pure rubbery flavor. Are the gromets going to crap? These things should be built for Sub-Ohm Vaping!

I have no clue what's wrong but I can't use this thing anymore.

I'm also getting more juice in my mouth than I would if I drank it. These coils have started to spit and spew like nothing I've seen. I've used these coils for months and could always go up to 30 watts, no issues!  

Hey all.

So I've been vaping since January. I started out on a kanger ego and an aspire k1. Since then I've gone through aspire cf batteries, and finally made my way to my current set up. An mvp 3.0 or istick50w with my subtank mini.

At first using the stock occ coils with the subtank, I decided to buy some wire and cotton and here I am. Been building my own coils using the RBA section and loving it. I wick it properly and never get a dry hit, going anywhere from 18-25 watts, which is my preferred settings.

Now, it's only my preferred settings because I can't seem to go any higher. On either device. I get dry hits like crazy despite pancake wicking which I've specifically done to prevent said dry hits. I always have heard that it can possibly taste better the hotter it gets. And I don't mind a hot vape. But it won't let me try!

I'm well saturated, well wicked, and my juice can be anywhere form 50/50 to 70/30pg. I can do quick pulls on fully open, and slower toots on the middle setting on the subtank. I just can't go any higher than 25watts and I don't know why!


And that's not for just the coils I built. It's for the stock occ .5 ohm coil as well. And like I said all my cotton is beyond well saturated. Any help?  

Im new to external battery mods but have been vaping for 3 years and I know how to prime a coil with e-juice. I go the extra mile after I prime the coil and let it sit for a minute. Then I fill up the tank put it back together and do not touch it for at least an hour or two just to make sure. I just got my now verified as legit sigelei sobra with the moonshot 120 both of the coils from that taste like those knock off BS eBay fake coils. I started off at a very low wattage and I don't know what's wrong both coils are disgusting. It's not exactly a burnt taste or a dry taste it's like a sour off taste and I can't use them. It also makes me feel like I have something in the back of my throat. What in the heck is going on? Do these coils take awhile to become usable? They're the coils that came with the mod and I verified the mod so I assume the coils are also okay. I even went so far as to try the second coil on a different mod but with the same tank just in case the mod was frying things the very first hit. Can anyone give me an idea of what's going on so I know what I need to do and also if anyone could tell me whether or not the Cascade baby coils will fit in the moonshot 120  

Ok so I know that kanger subtank .5 ohm coils are good for up to like fifty watts and the subtank 1.2 coils are good for up to 26 watts, my question is this kanger has released vocc coils pretty much the same coils they have for the aero tank , genitank ,etc except now they have organic cotton like the subtank coils. Is it safe to think that the 1,2 and 1.5 ohm vocc coils will be safe as the 1.2 and 1.5 subtank coils at the 26 or so watt range, if not how many watts are safe so I don't burn them to hell  

ok ... so there was a thread that showed insect droppings in some cotton someone got with a RBA ... but I can't seem to find it.

So I thought I'd have a look at the cotton sample in my Kanger Subtank Mini & .. sure enough ... bug bits & little black "dots" (bug poop I assume). Okay ... fine ... I've not used it & will not use it. I have enough cotton (bacon) to keep me going for years, and I'm happily puffing away on the .50ohm OCC premade coil supplied by ........

........and then it dawned on me that it was supplied by the same folks that put a wad of bug-gunk-ridden cotton in the box with my ST mini ... Kanger.

So ... the question is if anyone has taken apart the OCC coils & found little black specks in the cotton, or other foreign "pieces" ?? I'm wondering if the cotton Kanger uses for the OCC coils is the same cotton they give you in the box to wick the RBA deck with.  

So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again  

Starting from a clean - authentic nautilus mini - with a brand new 1.6 (or 1.8 it makes no difference) coil (coils also verified as authentic).

1. Turn tank upside down - with tip removed and fill with juice.
2. Take base unit and set so no air holes are open.
3. Put a tiny bit of juice around the o ring of the base unit (i get the issues if I do this or not)
4. Put 2 small drops of juice into the coil (I get the issues if do this or not)
5. Screw the coil into the base unit (as tight as you can comfortably get it without going past the obvious stop point and damaging something)
6. Screw the coil/base unit into the tank.
7. Turn nautilus mini correct way up.
8. Move air hole to a middle setting.
9. Take some primer puffs with no power.
10. Leave standing for 5-10 mins.
11. Begin vaping gently at 6 watts - moving up slowly to 10.

Ive tried all types of juice - both high VG and high PG and in-between. Invariably at some point i start to get the gurgle. Ive tried the following fixes:

1. Using a paper towel blow gently out of the air hole to get rid of juice - doesn't work - if i kept on blowing id blow the whole tank of juice out.
2. Take the unit apart - most times there will be juice in the base unit underneath where the coil sits - dry this out - dry the coil off and repeat from step 2 above missing out steps 3 and 4. - this sometimes works but its a temporary fix.

There seems to be no pattern to the problem. Sometimes the gurgle starts as soon as ive changed the coil - sometimes its ok for a week. I have 2 units and 2 spare tanks and have rotated them all using the above method - still get the issues.

I have actually never experienced the burnt taste or reduced draw because Ive always got sick and binned the coil before that point.

I am vaping generally at 9.2 watts - but have tried as low as 7 and as high as 13 - it makes no difference.

I don't draw hard - I cannot understand why I keep getting juice in the air chamber - its not a problem with a "dud coil" unless they are all intermittently dud coils - they are all authentic aspire and I've bought them from different places - so its not a dodgy batch issue - the rings are all the correct way up - I have spent hours and hours researching to try to fix these issues - and cannot for the life of me maintain a stable nautilus mini.

Can anyone save me from madness and tell me what Im doing wrong - Im tending towards a conclusion of all nautilus mini components are junk at the moment.

Many thanks in advance  

So I got my Lemo 2 yesterday and there is something wrong with it . The taste is awful . I boiled the crap out of it yesterday but that didnt change much .

Basically I get bad taste even if my cotton is oversaturated with juice which leads me to the conclusion that this taste is coming from the tank itself . I checked everything its fine , the pressure is also fine . That bad taste is a mix between a dry hit and plastic taste but agian , taste doesnt change even if I full my entire chimney with juice so it is not the whisking . ]

Has anyone had similar problems or any ideas ?  

Hello everyone. I am new to the forum but I have read a few more topics before having to create an account and explain my problem in detail. I own a Geekvape Aegis Mini TC 80W (with the Cerberus tank) and I'm using a 50% / 50% e-liquid, with chocolate, coconut and oats from Nebula. I have owned it for about 2 weeks now. I've been using a .3 ohms coil in these weeks, and I've been really good, except for the last 2 days, I've burned the coil slightly and I don't like the taste anymore, so I decided to switch to the other .2 ohms that I've bought a couple of days ago, so I primed the coil by putting 4 drips in each cotton hole + 2 or 3 drips in the center cotton (it's a mesh coil). I forgot to say that I vape mainly from 30-40watts but it's fine even from 25-42W, I'll never go over it because only the noise scares me. Yes, I know, it's weird. Anyway, my problem is that after switching to a .2ohms coil (it's been about 30 minutes) at 30watts the taste is yucky, totally different, I wouldn't say burnt but not good, plus the noise is like it's muffled, yeah , I opened the holes, if I go over 30 watts the noise gets slightly louder but the taste worse. I would just like to know if I have to leave it overnight to let the liquid absorb well or change the coil directly because it is faulty (I have another 5 of .2ohms but no other so I can't go back to .3ohms)
So, is this normal?