No Point Using Sub Ohm Coils On A Vw Mod?

Any suggestions for an inexpensive DNA 40 mod capable of firing the new Kanger 0.15Ω coil ? Need to know price for whole set-up including mod, batteries, and charger. Already have the Subtank Mini.  

Hello vapers! first! I'm a noob at this stuff because I just buy my tank and use it with the coils it comes with and second, my english isnt that good but I can understand it perfectly fine.

Anyway, Ive been searching everywhere but I couldnt find a solid answer to my question.
Im using an Aerotank Giant right now with a 1.8 ohm coil, if I put a 1.2 ohm I would have to use less voltage because I get a burnt taste and the coil burns pretty quick, Im about to order a Sub ohm tank soon and I'll use the stock coils, the one im getting is the Kangertech SubOhm tank.
Why do subohm coils use more voltage when normal coils use less?

I mean, Ive seen people do things like 0.2 ohm coil @ 100W + If I did anything over 3.5V on my 1.2 ohm coil itd burn instantly... SubOhm takes more voltage the lower you go and normal dual coils take less voltage the lower you go!

1.9 Ohm Dual coil = 3.7-3.8V for me
0.5 ohm OOC subtank sub ohm coil = 12-30W?!

Thanks in advance for taking the time to reply to this post and your patience!

Cheers!

Edit: by the way, Im planning to use my subtank with a 50/50 PG/VG 16mg nicotine, Is that ok?  

Hello,
Does anyone know why with the original Subtank mini the coils that came with it were
a .05 ohm coil and a 1.2 ohm coil i have noticed with the new subtank it comes with a .05 ohm coil and instead of the 1.2 ohm coil it comes with a 1.5 ohm coil
does anyone know the reason for this
thank you  

Wich is the best (clearomizer) option for istick 30w?I know that MELO was specially made for 30w one but I don`t know,maybe you know a better than this.I want with replaceable coils.I was thinking at Kanger SubTank plus v2 with 1,2ohm coil,Delta II with the same 1,2ohm coils,Aspire Nautilus mini BVC or the MELO.
Now I`m waiting opinions for those who know!  

Dear forum!

here goes my strange experience:
I’ve been coiling and wicking for years pretty much the same way, and it was kinda ok = I adapted to all the quirks I had.

Recently I built a new coil, but instead of 4mm I decided to make 3.5mm coil. Same wraps number.
Wicked it as I alway do - exact same material, thickness (adjusted to coil diameter of cores) trimming etc.

And wow!
No problem with TC now!
Works reliably, no leakage, I can chain wape the whole tank!

could this one Change in coil diameter choice did the trick???

Or is it a fluke? (Well I’ll find out when I’ll built next coil same way...but still)

best regards
Vadim  

hey everyone i have a Smoke M50 with a new Arctic tank and it works fine with the .5ohm coil but i can t get it to work with the .2ohm coil and i cant figure out why. my friend has a sigelei 100w + and it works fine on his ugh..... if someone can help that would be awesome  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

Hey guys whats up. Well I had gotten the Sub Mini tank, the first tank I got was a dud. I had nothing but issues with it since day one. Coils went bad in 1.5 days both coils, then the rba deck was giving my sigeili issues and errors.

So I sent it back, They replaced it, and I now have Version 2 as they say. This tank has 2 air slots and different Holes in the tank. I used the Stock .5 coil but was just getting wayyyy too many dry hits.. So I went to the RBA deck, been using the coil that came with it, and I have 100% organic cotton. So I been using that, but now I am getting Dry hits with this thing!!! every 4th hit Is Dry!! I have to cover the holes and pull to get teh cotton wet again, and then 4th hit shes dry again.

What is going on here? Anyone else have issues like this? I am really getting fed up with this and ready to just throw it away. What can I do about the situation or why is this happening?

E-juice = 80/20 Clear Liquid all fruity flavors 3MG  

I have a battery that is capable of going up to 6.0 V but the chart that came with the battery did not have 1.6 Ohm listed on the chart, it skipped from 1.5 Ohm to 1.8 Ohm.
I just need to know what the max amount of volts that I can use with this coil without reducing it's life expectancy to much.

- Also is there any reason to prefer variable wattage mode over variable voltage? because I always use V/V mode never even tried V/W.  

okay, so i had a problem yesterday where i would keep getting juice popping up on the draw, that problem is solved, however, now on only the second day of light use, on the 1.2 ohm coil that came with the tank i am getting a pretty harsh smokey taste. Its not overwhelming like it is when a coil is burnt out, just an unpleasant taste. I did 4 drops of liquid on the coil before using, everything is screwed in tight. Do i need maybe a couple more drops on the coil?

FYI: using an istick 30w burning at about 14.5-15w