How Is This Even Possible

So I've been using a Kayfun v4 and provari p3 using the hybrid connector and have never been able to get th ohms below 2 using .2mm guage kanthal bought from Vape escape one 2 mm coiling tool and about 6 wraps was initially happy with that but after reading the results other users are having they typically end up around 1.2 1.4 ohms using far more wraps then I have been using I tried to increase my coil diameter to 2.5 mm and the ohms exploded to 5 ohms making it unusable I have noticed that my spring in the Kayfun gets incredibly dirty and charred with what I can describe only as soot if anyone has any insights into what could be going on I would much appreciate it ive been enjoying my Kayfun but I'm still looking for that mind blowing Vape I keep reading about  

I just Started rebuilding my kanger dual coils and im having a issue , seems like when i build them and check my ohms on my meter they are right where i want them but when i put them in my tank and fire them up the ohms fluxuate like crazy from low to high ohms, any idea why it happens ? It occurs even when i build single coils. Anyway to fix this? Thanks  

I never used anything but Kanthal and Nichrome wire to build my coils.

All things being 100% equal (wire gauge, coil type, coil diameter, ohms, etc) do SS coils require more power to run to get the same vapor as the exact same coil/resistance made from Kanthal or Nichrome wire?  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

Just a little warning to all who have purchased the Lemo 2- Do not use the wire included in the box.
I was a little worried when i was using the stock coil and noticed it had been turning a green color after a few days of use, not sure if this is the case with all Lemo 2's, but if you notice your wire is turning greenish, just throw it out and replace it. I don't believe this is kanthal, it could possibly be nichrome, but it's properties are not matching up with those of kanthal. My worries were confirmed when I decided to put a parallel 5 wrap coil on my rda with that wire because of my lack of other 24 gauge... Well today when I took out my cotton and dry burned the coil a little to rid it of excess juice, the coil actually deformed and somewhat melted on my rda . I don't know what kind of metal this is, but I'm positive it is not kanthal, this has never happened to me with kanthal, and this wire seems to be of a lower resistance than kanthal. Anyway, just wanted to let ya'll know to be careful with that wire, or just throw it out altogether. Otherwise, the Lemo 2 is a fantastic tank  

Just finished up my first build using 24 Guage kanthal with 9 wraps. It's a dual coil build that came out to .49 ohms. It's not the best looking build but for my first attempt I guess it's not too shabby. It was built on my mutation x v4. 40-45w was about as high as I could go before it got too hot for my liking. just wanted to share it.  

sorry for newbie question I tonight dove into the RDA world and bought a derringer some wire and a smok ohm meter, I have a hcigar hb 50 and my dual coil build on the HB shows .05, when I try to check it on the ohm meter all I see is 3 dashes no reading at all what am I doing wrong with the ohm meter.  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

Hi guys,

Is it really normal for an atomizer to get hot especially when using dual coils?
I just created a dual coil a couple of minutes ago using 24 gauge kanthal wire, 10 wraps each on a 2.4mm precision screw driver. My meter shows that the resistance is at 0.4 ohms, being curious and all since this is the first time that I made a dual coil, i decided to test it out.
Got some good flavor and vapor, though the vapor is warmer than I would want it to be ( I prefer cold vapor)

After taking a couple of 5 secs drag, I notice that my atomizer became hot, not warm, but hot. Is this something that I should be concerned about? I am doing something wrong or have I done something wrong when creating my coils?
Please help.

Here are some pictures of my device and atomizer. ( Philbox wood mod running on 2 pcs of AWT 18650 2600mah battery, my atty is Haze by vapehead origins)


 

Hey all, I've been vaping for 3 months. I DIY and I have been using the same flavors, vg, pg and nicotine and I have never had a problem. But the last few days I have been getting a tight chest and it hurts and makes me cough when I inhale? At first I thought it was the custard, but it is happening with fruits too. So I am wondering if my current build in my RDA could be the problem? It's a simple single coil build 10 wraps for 1.5 ohms and I usually run it at 4.7volts. Couls someone give me some insight into this? is it possible my build has a short that I am not aware of? ohms are not jumping and it heats evenly. So I don't know.

Please help! Ive invest a lot of money into vaping and I dont want to stop.