Hey guys. I have been in the vaping scene for a little while now. Just curious to what everyone likes to sub-ohm with.
My favorites so far.
Mutation X V3- 24 gauge dual parallel 5/6 wrap
Mutation X V4- 20 gauge dual 5/6 wrap or dual 6/7 wrap
Turbo RDA- both of the above builds work well
I've had the dark horse, doge and doge v2, freakshow, and a few other RDA's and the 3 above have been my favorite....v3 was my favorite for a while until I tried the v4, its now my favorite, and its a tie between the v3 and turbo for 2nd and 3rd place.
What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)
And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...
(I know preferences may vary greatly)
Thank you very much
:
Sent from my iPad using Tapatalk
so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.
I also have the aromamizer titan.
What gauge would you Clapton?
Sent from my HD1907 using Tapatalk
One of my 18650 batteries had a snag so I did my first re-wrap. I thought I had it positioned well before turning on the hair dryer but seems I got way more wrap on the pos end than on the neg end of that Samsung 30-Q. Here it is next to an original wrap. There's not much wrap at all on the negative end. Do you think it's ok or should do over?
Was wondering about everyone who makes their own coils, what is your favorite builds? Do you stick to single,dual,triple coils? (or higher) would love to see pics if possible Heres mine, a bit blurry
Hi guys!
I'm genuinely curious what all you beautiful ECF members have ultimately figured out to be your general all-around favorite vape configurations that you've figured out. I know we all have different tastes and preferences, I just think it would be cool to see what others have settled on to be their ideal daily vape.
So share that yoda-like wisdom that you've discovered so far! I guess to guide in a general direction I mean you're favorite:
-toppers
-mods (or battery power)
-coils & wicks
-settings (wattage, temperature, volts, ohms, regulated/unregulated, whatever's pertinent)
-Favorite E-liquid(s)
-Anything else for the setup you go to work with, sleep with, wake up with ETC.
I think we could all learn from each-other by sharing the cream of our crops per se! And if you have pics, post'em if you got'em!!!
It's me again Margaret!
I've been gone for awhile due to a new job and new hours, not enough free time but i'm back.
I started on an Ego-T, and a tank you couldn't tilt over without spilling juice.
Since November, I have dove head first into the deepest realms of vaping.
Now I vape using a Sigelei 150w set on 80w usually on .4-.6 builds, dual, single, quad, parallel, twisted, ranging on a few different RDA's, (Authentic Pollux, Dark Horse, Little Boy, Magma, Doge, and Enigma).
If I get 10 replies, with pictures of your vape box or vape collection, I will post mine!
I want this to catch on!
LET ME SHOW YOU WHAT I HAVE SPENT ALL MY SAVED CIGARETTE MONEY ON!!!!!
SHOW ME YOUR VAPE COLLECTION!!!!!
I've mostly used tanks but now I want to start building coils on my mutation rda and doge rda. I'm looking to want to build between a 0.2 and 0.3 ohm coil. How many wraps and what drillbit size should I use? Thanks!
Been building my vape hardware collection lately and at at the point where I wouldn't mind another good subtank, but it must have an RBA with it. Gotta be able to rebuild it! hah
My current lineup includes a Subtank Mini on the XPro M80 Plus, a 30w iStick, Doge, Dark Horse (by FAR my favorite RDA I've had or tried), and a Hades Mech. All decent stuff but I'd like to have another tank for my collection. What's a good (and decently priced) tank to go with my Subtank? I'll say this, I've tried the Atlantis and didn't care for it so don't suggest that. Any other suggestions?
My buddy wanted me to show him how to wrap up some coils. Hes using a vamo v5 and he bought an orchid v3. He doesnt like harsh draws but rather a smooth, light, cool pull. So i decided to try that standard wire that comes in the orchid v3's package. Its that stock, hair thin wire that comes in the box with most of your typical RDA's RTA's, but i cant figure out the gauge dimension on it. Im trying to get him a whole roll of it so he can wrap his own. If you guys can help me out i would appreciate it. Thanks!
So no mine didn't melt haha but I was wondering what the best build would be for a plume so I could prevent this? I normally go with a .3 ohm build 24 gauge 7 wrap so yeah thanks guys!