New Build With 24g

I just got some japanese cotton pads and I have been building my rba section in subtank for a little while with organic cotton balls and have noticed that after I take a puff off of it I get this sizzling after I let go of the button I've read it could be to much cotton but I tried a very little amount of cotton and still get sizzling.. I'm using twisted 30 awg. Reading at .4 any idea?  

Hey all, I've been vaping for 3 months. I DIY and I have been using the same flavors, vg, pg and nicotine and I have never had a problem. But the last few days I have been getting a tight chest and it hurts and makes me cough when I inhale? At first I thought it was the custard, but it is happening with fruits too. So I am wondering if my current build in my RDA could be the problem? It's a simple single coil build 10 wraps for 1.5 ohms and I usually run it at 4.7volts. Couls someone give me some insight into this? is it possible my build has a short that I am not aware of? ohms are not jumping and it heats evenly. So I don't know.

Please help! Ive invest a lot of money into vaping and I dont want to stop.  

So I finally got around to putting a coil on the rba deck...my typical kayfun build, 28 ga @ 1.3-1.4 ohms. Everything looked good, coil tight....raised off the deck...screwed into the ohm meter....weirdness ensues....said 3.85 ohms...took it off, put it back on...said 4.6 ohms....looked to see if the coil screws were tight ...check. both tails tight under the screws...check. The coil deck screwed into the base...yep. No moisture in the base, nope. Put it on the ipv...said 7.7 ohms, then 4.2, then 3.90.............


Put the stock coils in the base, everything normal. Is there something I could be missing in the coil deck??? I got nothing else. No, I had not put the chimney on, so no short there. I may wrap another coil and see....I can only think that something is amiss in that little coil deck....or I am missing something in the build that is obvious. It's a really nice, tight looking coil too.  

Just finished up my first build using 24 Guage kanthal with 9 wraps. It's a dual coil build that came out to .49 ohms. It's not the best looking build but for my first attempt I guess it's not too shabby. It was built on my mutation x v4. 40-45w was about as high as I could go before it got too hot for my liking. just wanted to share it.  

Hi everyone, I'm looking to build my kayfun 4 clone (infinite) to accommodate high vg Bobas bounty any ideas are welcome, I have 26, 28 and 30 g kanthal along with organic Japanese cotton. May the moderators let this thread fly for the night as when they push it to the builds forum I lose the most of the forum input,
Thanks  

So i build my coils, but i wanted someone get my wraps tighter, so i asked a friend, and he recommended me too one of our vape shops. the guy there said $5 per coil and 5 for wicking, is this just outrageous or whats the normal price for a build  

New to rtas and using hellvape md I use 6wraps ss 28ga wire and cotton bacon prime and the thing is my vape makes popping sound all the time....my zpide tank used to pop also but didn't sound so loud I guess cause the rta has the chamber but I was wondering is that normal thing??? I tried wick veeeery tight like I didn't care if I get dry hit just to see if the popping would stop but didn't ...
I tried to go to lower wattage but then I feel like the juice boils and makes me scared I will get flooded coil and higher wattage don't help...do u guys get popping sounds when u vape ? Is it normal? Am I doing something wrong that I can't realise???? XD  

I have recently purchased a DNA 40 device and feel like I have lost all my build knowledge!! I am using awg 28 wire if I do 10 wraps on a 2.5mm drill bit I get a reading of around .13 on any of my devices if I replicate the build on the Lemo it comes out .27 or above. What is going on can someone share any light on this?


Sent from my iPhone using Tapatalk  

I recently picked up an infinite origen v2, my first build was single coil 2.4mm and it was not good on flavor, next build was dual coil 2.4mm at .5ohms, it was better on flavor. No matter what single coil build I try the flavor is just not there. Any suggestions on great flavor builds???  

What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)

And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...

(I know preferences may vary greatly)

Thank you very much

:


Sent from my iPad using Tapatalk