Do The Authentic Subtank Coils Have The "red Ring"?

I am kinda a noob when it comes to prebuilt coils. I am looking for coils that feel very strong/sturdy, but I am not sure what material it is.

I had coils that said they were .25ohm and all it says is "KA1 WIRE + Ni80 wire" and they felt very sturdy/hard to pull the wraps apart etc....

I bought what I thought were a good replacement for those, but they feel flimsy and easy to pull apart the wraps. They are .36ohm, 316l stainless steel, 30gx4/36g.

So apparently the stainless steel wires are more flimsy...I cannot seem to find coils that have KA1 + Ni80 like the sturdy coils I once had. I
am trying to figure out which material/what I need to look for in order for the coils to be sturdy like the old coils.


Can someone help me out with this? Thanks in advance.  

Hey guys I'm looking to upgrade from what I have right now which is the atlantis v1. I'm not a huge fan of the atlantis because of the inconsistency with the coils and the loss of flavor after 2 tank full. The atlantis v2 seems nicer with the occ coils and improved airflow, but I'm not sure if its worth the upgrade since I could just get the new 5-pack occ coils for my v1. The subtank mini still has better options with the occ coils and RBA. Also it seems the occ coils for the subtank is easier to rewick which could save me a few dollars.
I'm not sure which one to go with. I'm leaning more toward the subtank, but still not sure. Maybe someone who has either one or knows more about them could help me. I like to have a good amount of clouds while still keeping the flavor.

Or if anyone has a sub-ohm tank they could recommend that they like more than the ones I mentioned that would be good too.

I use an ipv2

Thanks  

Hi all,

I've recently decided to buy a Kanger Subtank Mini to test the waters out and see how it compares to the Aspire Atlantis. Unfortunately, my coils are only lasting me 6 hours at the most before the cotton is charred black and everything tastes burnt. I've heard about coils that are coming back as duds. What is a good way to tell if the coils I've bought are duds?

Thanks in advance!  

Ok so I know that kanger subtank .5 ohm coils are good for up to like fifty watts and the subtank 1.2 coils are good for up to 26 watts, my question is this kanger has released vocc coils pretty much the same coils they have for the aero tank , genitank ,etc except now they have organic cotton like the subtank coils. Is it safe to think that the 1,2 and 1.5 ohm vocc coils will be safe as the 1.2 and 1.5 subtank coils at the 26 or so watt range, if not how many watts are safe so I don't burn them to hell  

I'm using a Subtank Nano on the KBOX. Should be absolutely no problems.

But my coils (both the 0.5 and 1.0) are tasting awful. I prime them great, I make sure everythings good and secure, and I'm using a 75%-ish VG juice.

But I can't go above 20 watts with two new packs of coils I have, and especially on the 1.0 coils, that's ridiculous. I'll get a vaporized rubber taste that tastes like the worst clearomizer coil I've ever come across.

Dry cotton should just have sort of a cottony, almost doggy or smokey taste. But this is a pure rubbery flavor. Are the gromets going to crap? These things should be built for Sub-Ohm Vaping!

I have no clue what's wrong but I can't use this thing anymore.

I'm also getting more juice in my mouth than I would if I drank it. These coils have started to spit and spew like nothing I've seen. I've used these coils for months and could always go up to 30 watts, no issues!  

I recently upgraded to the Istick 30 and Subtank nano, and kinda want to try out a dripper, but do not want to build coils, check ohms etc. Are there any drippers available that take pre made coils? I guess I can wick if needed, but I'm not ready to jump into coil building yet. And if anyone could explain the benefits of dripping over a tank system, that would be great also I know changing flavors without dumping a tank, but any flavor or vapor advantages?  

I'm new to vaping. I've went through 3 coils barely using them.


My issue is: When I first install the new coil and add the liquid, it produces vaporizes just fine. It seems like when I set it down for an hour or so, and go back, it still produces good vapor. But after a bit, if I set it down after vaping, and go back, it produced no vapor no matter how much I puff it. It seems like if I unscrew the part where the coil is, and run it under water, and then let it dry, and replace it, then add e juice, it'll start producing vapor again. But it seems like as soon as I set it down for a bit, and pick it back up, there's no vapor and I wash it out again, etc then it works, but eventually just stops producing vapor altogether u til I replace the coil.

What's going on here? am I doing something wrong? Do I need to adjust the coil some how? I've bought brand new coils and barely use them and this happens. Is the coil just getting gummed up? The coils don't make vapor after so long, and the usage doesn't even equate to a full day, maybe an hour or so.  

so i have a COV ARIS atty that i bought about a year ago. i took it apart to try to increase the airflow, but got sidetracked on that project and put it on the back burner. Fast forward 6 months and i go to start the project again but i had lost the insulator to seperate the center post from the atty body. i tried contacting COV with no luck. Anyone have any ideas on where i could get an insulator for this? or if i could possibly make one?
thanks in advance
-Matt  

Okay so I bought a pack of 5 coils from FastTech as I needed some coils, they arrived today and well.. they don't really look too good. there like barely any wick on them! and the rubber seal thing on it is tiny.. all I need to do is just look at it and know it's going to just leak and gurgle and ew.
Here's a pic;

Should I put a bigger rubber seal on it? There's barely any silica wick on these things I'm quite disappointed really.. Don't know what I expected ordering from fasttech but not that!

Any ideas on what I should do with these? :/  

So my husband and I bought two zenith II tanks and inokin 1.6 ohm heads. My husband has not been impressed with the lack of flavor that it produces. Mine has been ok but I’m wondering if I need to clean the coil often? I usually use a nautilus tank and coil that I would clean each time I added liquid. Any help is appreciated as we bought 13 packs of these coils