I'm not quite sure what the difference is between operating in VV vs VW is. a worker at a B&M said I'll get more "performance" out of VW mode ... But in my mind Ohm's law rules. If I run my Atlantis .5 at 4.2 volts, that's 29.4 watts. I understand that I can up watts a bit without affecting the voltage reading (maybe it affects it beyond the decimal places the iStick 50 can display?) but am I theoretically squeezing any more performance out of the coil? I'll be honest and say that it only makes a difference when the wattage reaches the borderland between one voltage output and the next and even that seems to be very minor.
I hope that makes sense. IOW, if I like the vape at 4.2 volts, then am I actually gaining anything by upping wattage without changing voltage? My initial experiments tell me "not really," but the science part of my head wants a better answer. Maybe I'm missing something?
vaparroos,
so here is a chart: http://i.imgur.com/6oraBGI.png
this charts says if i have a 1.2 ohm in my kanger subtank that i can vape at 6.0 volts at 30 watts and be ok, but i know that is not the case...
when i'm vaping at 1.2 ohm at 3.8 votls its ok, but i'm in the orange too...why am i still in the orange at 6 volts?
hope that makes sense...
Hi, I was thinking about buying the Kanger 1.2 ohm enclosed wick but am not sure exactly what wattage or voltage to use. I currently use the Protank 3 on my Istick 50w. I am currently using the 1.5 ohm wicks and run my device at 9.2 watts and 3.8 volts. So I was wondering if this is right and if I should up the wattage for the 1.2 ohm coils and leave the voltage the same?
Hello,
I've set my Smok xPro M65 with my Kayfun V4 on 15 watts at 0.8 ohm. However, the volts are changing frequently on vaping. Ohm and Watts stay the same just sometimes on vape the volts display 3.4v, the next time its showing 3.6v and changing etc ... its weird because ohm and watts are the same .. just volts change .. what may cause this ?
Kind Regards.
I have been vaping for 1 year and 3 months now, I have been using an ego twist VV and I usually vape the same liquid all the time, I vape it in an evod with 1.8 ohm resistance and I vape at around 3.7 to 3.8 Volts.
Question, I just bought and received a Vamo 5 today and got two original Panasonic 18650 batteries, everything is fine. My evod works great on the Vamo and I use it at 3.7 volts just like I did on the ego twist. My question is this, what is the difference between vaping using voltage or vaping using wattage and which should I do and why in reference to my Vamo 5?
Also if I use voltage setting does it auto adjust the wattage or if I use wattage setting does it auto adjust the voltage, also what is the advantages and disadvantages of both in the Vamo 5?
Thanks!
I've always wondered whats better for efficiency. In a regulated mod I can't imagine it really makes a difference in vape performance, I'm currently keeping my builds at a lower resistance by winding parallel coils. My goto build comes to about 0.4ohms and I run it in the range of 28-38w, usually set at 32w, if I wound it in series it would be around 1.6ohm which would need about 7v to get to 30w and at my Aegis solos max voltage of 8v would provide 40w. The only issue with this is that it limits the wattage range you can run at, since I sometimes do crank this build upto 42w, although it does start to burn above 45w.
The one advantage of running at a high voltage and a lower current is that theoretically there should be less energy loss in the transmission of power to the coils (like in the pin, the posts and the wiring connecting the 510), although depending on the construction of the mod/tank it may not be significant enough to provide any benifit. I can imagine that it's not that simple either as the mod is having to boost the voltage more which may cause the voltage conversion efficiency to suffer. Although in my dual cell mod it may be benificial since the input voltage is around 6.4-8.4v, although I tend to use this for my higher wattage builds.
This may just be me because I'm obsessed about how much voltage is dropped across cables, I always use the high quality wiring and keep it as short as possible because it is actually quite surprising how much energy you can loose through a cheap cable. Even good quality wire at higher amps can drop a significant amount of power.
hi all
I have a mvp 3 and I use iclear 30 tanks 1.9 to 2.1 ohms
im vapeing at 12 watts 5.1 volts and have been for a few weeks now
everything was fine until today right now in fact hence the reason for this question
I refilled my tank and screwed it back on my mvp when I pressed the button to vape
it reads the ohms and volts and wattage the wattage was as normal 12 watts
the volts were 7.1 and the ohms were 6.0 totally unvapable and burnt tasting
(I should also point out that the volts and watts are locked in on the mvp)
I have also tried the tanks on other devices and still the same issue
which leads me to believe its the tanks at fault and not the device
I have been vapeing long enough to understand the reasons for burnt taste
and the causes and solutions to rectify it but I have never had this happen before
I tried other tanks and the same has happened except for one which works fine
does anyone have any idea whats going on
thanks
steve
I have a battery that is capable of going up to 6.0 V but the chart that came with the battery did not have 1.6 Ohm listed on the chart, it skipped from 1.5 Ohm to 1.8 Ohm.
I just need to know what the max amount of volts that I can use with this coil without reducing it's life expectancy to much.
- Also is there any reason to prefer variable wattage mode over variable voltage? because I always use V/V mode never even tried V/W.
I have a variable W/V battery and I prefer it on 4.2, but it is expensive and I never get the full 300 charges out of them like they claim they are supposed to get. Will decreasing the voltage by 0.4 Volts increase the battery life to a significant extent that makes it worth while?
Little confused here...so I've got this piece of equipment with the up and down arrows locked at say 4.8 Volts. I notice that sometimes even with the button locked Ill pull it out of my pocket and see that the volts have changed to 4.7 or even 4.6.
So naturally I try and change it back to 4.8 and it reads "locked"
How is this changing with the lock feature enabled?
So I decided to try a 1,6 ohm coil on kayfun v4 clone Tobecco and I am using 28gauge Kanthal with a cotton
wick on a Rdna 30 and its vaping well at 15 watts I have a kanger subtank mini coming in the mail and here goes my question
So the kanger subtank states that with a .5 ohm coil i could vape up to 30 watts but the voltage comes in at like 3.8 volts
I was under the impression that the rdna 30 needs at least 4 volts to work which kinda brings me to my second question
What is the point of of sub ohms? cant i just build a 2.0 ohm coil or something like that to achieve the results as if i was subohming
I am very confused on this
thanks for the replys in advance
Oh yea is a 1.6 ohm coil at 15 watts a normal build or any recommendations for the kayfun v4 for watts and ohms thanks again