What Would You Call This Build?

What is your go to single coil build in terms of gauge wire, diameter, and number of wraps : (no fancy Clapton or twisted build just a "regular" wrap)

And if you have a reason please include it: For example: "I'm a flavor junkie and this is best flavor build I've found" or "I like short ramp up times" etc ...

(I know preferences may vary greatly)

Thank you very much

:


Sent from my iPad using Tapatalk  

I am trying to get the best flavor with the best single coil build.

Objectives:
Flavor Smooth Vapor
Materials:
Kanthal Wire 35mg Nic Salts
I have noticed that either depending on the diameter of the coil or the spacing of the coil wraps You get a different kind of vape hit. It seems like higher gauge wire produces a smoother hit. And then couple that with a small diameter coil build, plus squishing the coil together to remove all coil spacing results in the smoothest possible vapor.

Can anyone confirm my findings? Or does anyone have any tips because I have still to replicate the smooth hit from clearomizer sub tank cartridge's that are non mesh. I am starting to think this is because the cotton is wrapped around the outside of the coil instead of being shoelace through the middle of the coil.  

so in my pursuit of vaping above 200 Watts I made a fuse 3x24ga gauge wrapped with 36 gauge and I tried three coils. it came out .07 I Vaped it at about 375 watts it was a hot vape but the ohms were very low so I had a problem with power my DNA 250c was reporting 65 amp output so I took that and put in dual fuse 22ga gauge wrapped with 36 gauge I ran that build triple coil I used it at about 250 Watts. what I am trying to do is vape at about 300 to 400 watts with an ohm or .2 to .3. the inner diameter will be 5.5 or 5 mm I'll be using the kanthal core wrapped with 36 gauge and ni80.I'm trying to figure out what my next bill should be to try to vape above 300 watts the restrictions I have is it can't be below point 1 ohm or above .3 ohm I have two aromamizer plus has with the series deck The parallel deck a second parallel deck and a single coil deck. The single coil deck fit 6.36 mm.

I also have the aromamizer titan.

What gauge would you Clapton?

Sent from my HD1907 using Tapatalk  

Hey all, sorry if this is posted in the wrong place but I was wondering if anyone has tried a 24g coil build in the subtank mini rba deck and if it worked or not? Regardless I'm going to build a coil a little later to try and see how it works but I thought I would ask before hand on the odd case someone has tried, I've searched a bit and couldn't find anything, everyone seems to like twisted coils in these. The main reason I'm interested in doing this is because I've never vaped a successful tank with no burnt/dry hits yet so I figure the 24g ramp up time might help settle this problem, at least for me. I'm interested to see the thoughts so please reply  

Ok I'm hoping I don't get heat for these questions/statements but educating ones self especially with something that is still very new is important to me.

1. Read some articles on how there is second hand vape similar to cigarettes (99% better mind you) what are your thoughts? Vaping may not be as safe as smokers think, research suggests | Society | The Guardian

2. Formaldehyde found in builds running at high watts/voltage? But 0% at low/normal builds, what i can't seem to find is whats considered to high for a Mechanical Mod or even for a V/W, V/V Setup? My normal build for a mech mod is twisted single coil 24 gauge 6-7 wraps, usually gets about 0.28 ohms and single coil 8 wraps of 24 gauge puts out 0.73 ohms on my flavor builds.
Before You Vape: High levels of Formaldehyde Hidden in E-Cigs - NBC News  

I've been using only twin-18650 mods for some time, and before the shipping ban came into effect, I bought a backup of my most-used mod (a Geekvape Aegis X), but since the 100W single 21700 / 18650 Voopoo Drag X Plus was only $35, I also picked up one of them as another backup.

I vape exclusively on RDA's, typically with a 3mm dual coil twisted build with 24 or 26 gauge Kanthal or nichrome-80. 5 or 6 wraps with 24 gauge, 6-8 wraps with 26 gauge. I typically vape these between 90 and 110 watts.

I did not expect to get a 'true' 90-100 watts out of the Drag X, so I set a target of around 60 watts. I mounted a 3mm dual coil twisted 28 gauge build with 6 wraps, which on my Aegis X vapes great at 60 watts, and very good at 50 watts. It measures at 0.45 ohms.

But on the Drag at 60 watts, it only vapes at what feels like 30 watts on my Aegis. Setting it higher makes no difference either, it seems to 'top out' at ~30 watts regardless of the setting. 60 watts @ 0.45 ohms is only around 11 amps, so I doubt I'm hitting an amperage limit.

I am using 18650 batteries (VTC5A), and it is about time to replace them, as I am only getting around 70% the battery life as I did when new. I will be picking up some 21700 batteries at the same time, which hopefully help with things on the Voopoo.

Does anybody have any good experiences with ~60 watt builds on a Drag X Plus?  

Have you called yet? If we don't call we won't be heard. I told them I was against the vaping and flavor ban. But I'm one person. It can't be said enough. We ALL need to call. Maybe then they'll see they can lose their jobs if they continue to push these bans!

White house - 202-456-1414  

I found an "interim job" this week and decided to reward myself. I was originally stopping by the B&M to get another Subtank Mini as this job involves a 45 minute commute and I'd like another 'bigger' tank to take with me (almost got a regular sized Subtank, but it looked ridiculous on the VF and didn't feel comfortable), but they hadn't gotten them in yet, so as I was standing there browsing (as I always do if they don't have what I'm looking for), they said they got more RDA's in. So I looked, but wasn't thrilled with the one that was suggested first, so someone else suggested my new toy. It looks great on the VF! I already know how to build, but I asked about different flavor builds, so they sat down and showed me how to do twisted builds. They built me a twisted 28g single coil that reads ~0.6 Ohm. Holy cow the flavor! I know, I'm like a little kid discovering the swing set all over again for the first time. lol. So...what do you think of my new toy?

 

It's often been said to test a new coil build on a regulated mod before using it in a mech mod. Just for fun, I tested a new build on multiple platforms to see how consistent they a

These are AVS stainless steel premade quad core clapton 30x4/40 3.5 7/6
Two coils in a Dead Rabbit V2 RDA

Coil Master Tester 0.17
Uwell Crown mod 0.19
Wismec mod 0.18
Geek Vape Aegis 0.18
Vapresso Luxe 0.18

Closer than I would have thought!

Incidentally, the old coils were in there for 8 months, although this unit is in rotation, so maybe a months worth of actual use.

Also, the top cap was just about impossible to remove from the tube. I had to insert a chap stick into it and slam it on the desk for it to come off.  

I get so frustrated with people and trying to keep them informed.. I am Sick of hearing , "Wow thats a lot of Smoke" Or Go take your Smoke break" and calling it smoking flat out! I get sick of repeating my self ... Finally my Mother Inlaw has gotten the language down.. Vape shop not smoke shop and vapor not smoke, I wish others would finally get it! Anyone else having this issue??